The Baldwin offers the best of both worlds, bridging the gap between the demands of XC racer to the enduro rider. It features the tried and true Posi-Lock retention system protected by a robust 6061 CNC body providing extra support. -  Weight: 332g CrMo -  Body: 60661 CNC AL -  Spindle: Cromoly -  Bearings: 3 Cartridge  -  Springs: SWP  -  Cleat: XPEDO XPT (6° Float)

The Baldwin offers the best of both worlds bridging the gap between the demands of XC racer to the enduro rider. It features the tried and true Posi-Lock retention system protected by a robust 6061 CNC body providing extra support. - Weight: 292g Ti - Body: 60661 CNC AL - Spindle: Titanium - Bearings: 3 Cartridge - Springs: SWP - Cleat: XPEDO XPT (6° Float) *Titanium spindles have 180lbs weight limit.

Xpedo's designers went back to the drawing board for the GFX to create a fresh new design to meet the demands of the evolving downhill racing styles. The latitude entry system allows rapid engagement in any condition, positioning the front claw upwards for intuitive, seamless contact with the pedal. The Posi-Fit retention system is fully adjustable for fine-tuning the entry and release. The low-profile 6061 CNC body with adjustable height pins provide traction and support with any style of shoes. Tapered cromoly spindles roll on three precision cartridge bearings for easy maintenance. Wider Q-factor allows ample clearance between shoe and crankarm. - Weight: 468g CrMo - Body: 60661 CNC AL - Spindle: Cromoly - Bearings: 3 Cartridge - Springs: SWP - Pins: 16 adjustable height grub pins per pair - Cleat: XPEDO XPT (6° Float)

- Weight: 312g  - Body: CrMo Investment - Spindle: Cromoly - Bearings: 1 Cartridge/2DU  - Springs: SWP  - Cleat: XPEDO XPT (6° Float) 

- Weight: 220g  - Body: NEP Injection-Molded - Spindle: Cromoly  - Bearings: 3 Cartridge - Springs: SWP  - Q-Factor: ±53 (mm) - Cleat: XPEDO THRUST 7 (6º Float or Fixed)

The X-Fusion Manic post uses internal cable routing and was designed around a low-profile seat cradle and seal collar to fit a broad range of frames. The mechanism is air-sprung and hydraulically locked. The remote can be run on the left or right, above or below the handlebar, but is optimized as a left shifter replacement for 1x drivetrains. - Cable activated, hydraulic action, infinitely adjustable travel - Double key-way design prevents lateral twisting - Double bolt clamp with a wide range of seat angle adjustment. Fits both standard and 7 x 9 mm Carbon Rails - Sealed cartridge internals for quick replacement - Low profile head-seal and saddle clamp increase useable travel

Light, strong with extra tall teeth, the Wolf Tooth Aluminum Single Speed Cog is a lightweight option for single speed cogs that's offered in a variety of sizes. - Wide 4.5mm base won't dig into your freehub - Made of 7075 Aluminum Alloy for durability and lightness - Made in the USA

Designed for the XC racers. 5mm of 100% silicone compound provides excellent vibration dampening and superior comfort. - 100% Silicone weather resistant material - Plastic bar end plugs - 5mm thick

Wolf Tooth ShiftMounts are adapter mounts that allow you to integrate SRAM and Shimano shifters with several different brakes from Shimano, SRAM, and more. Handlebar space is prime real estate and the ShiftMount seamlessly integrates brakes and shifters for a clean look. - Designed to work with rear (right side) brakes and shifters - Consult the brake and shifter manufacturers to understand which mounting interface you have on your brakes and shifters - For handlebar clamp ShiftMounts tighten clamp bolt to 1-2 Nm max torque - 6061-T6 aluminum - ISEV-ISB is for a Shimano I-SPEC EV shifter mounting to a Shimano I-SPEC B brake

- ShiftMounts are adapter mounts which allows you to integrate SRAM and Shimano shifters with several different brakes from Shimano, SRAM, and Magura. - Handlebar space is prime real-estate and this ShiftMount integrates seamlessly for a clean look. - 6061 T6 aluminum - Weight: 8g - Made in the USA

- ShiftMounts are adapter mounts which allows you to integrate SRAM and Shimano shifters with several different brakes from Shimano, SRAM, and Magura. - Handlebar space is prime real-estate and this ShiftMount integrates seamlessly for a clean look. - 6061 T6 aluminum - Weight: 8g - Made in the USA

Wolf Tooth ShiftMounts are adapter mounts that allow you to integrate SRAM and Shimano shifters with several different brakes from Shimano, SRAM, and more. Handlebar space is prime real estate and the ShiftMount seamlessly integrates brakes and shifters for a clean look. - Designed to work with rear (right side) brakes and shifters - Consult the brake and shifter manufacturers to understand which mounting interface you have on your brakes and shifters - For handlebar clamp ShiftMounts tighten clamp bolt to 1-2 Nm max torque - 6061-T6 aluminum - MM-ISII is for a SRAM MatchMaker shifter mounting to a Shimano I-SPEC II brake - MM-ISII is compatible with M9020, M9000, M8000, M7000, and M6000 brake levers - MM-ISII is compatible with, but not designed for SRAM AXS because the shift lever will be further towards the end of the bar, or closer to the rider's hand than is ideal for most riders

Replacement Bar Plugs for the WTC Singletrack Pogie. - Quick install and removal of pogies via proprietary quarter turn bar plug mounting system

This stem cap is where your bike fashion sense and the weight weenie in you collide. This Ultralight and ultra-sleek stem cap integrates a 5mm, 10mm or 15mm headset spacer with your stem cap in finely machined piece. Why have extra steerer tube requiring spacers on top of your stem you ask? Well, many carbon steerers require that the steer tube extend above the stem. Also, riders may want the flexibility to move handlebar height up and down for different types of riding or for bike re-sale. - Design and manufactured in Minneapolis, MN USA - 1 1/8" top (straight 1 1/8" or 1 1/2" to 1 1/8" taper) steerer tubes only - 6061-T6 aluminum - 5mm internal cylinder wall height - Black aluminum bolt included Total weight (cap + bolt): 5mm= 12g. Compare to a standard flat stem cap and steel bolt at 20 grams + spacers add even more.

The GeoShift Performance Angle Headset allows you to adjust the geometry of your bike by changing the head tube angle, available in 1 or 2 degree options. This unique design lets the bearings sit at an angle to align with the steerer tube, preventing creaking noises commonly found with angle headsets that feature a spherical design. Reduce the head tube angle to make for slacker geometry and added stability on fast descents, or increase the angle using the opposite orientation of the headset, to make for steeper geometry and quicker steering with maximum front wheel traction. - Enduro black oxide coated chromium steel bearing included on both the upper and lower - Upper headsets ship with a star nut which can only be used on forks with steel or aluminum steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately) - Machined in the USA with lightweight, strong, durable aircraft-grade 6061 aluminum - Includes: Upper and lower cups, bearings, crown race, star nut, shims, stem cap with 5mm integrated spacer and bolt - 1 Degree Adjustment - Long version is designed for headtube lengths between 115 - 140 mm

The GeoShift Performance Angle Headset allows you to adjust the geometry of your bike by changing the head tube angle, available in 1 or 2 degree options. This unique design lets the bearings sit at an angle to align with the steerer tube, preventing creaking noises commonly found with angle headsets that feature a spherical design. Reduce the head tube angle to make for slacker geometry and added stability on fast descents, or increase the angle using the opposite orientation of the headset, to make for steeper geometry and quicker steering with maximum front wheel traction. - Enduro black oxide coated chromium steel bearing included on both the upper and lower - Upper headsets ship with a star nut which can only be used on forks with steel or aluminum steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately) - Machined in the USA with lightweight, strong, durable aircraft-grade 6061 aluminum - Includes: Upper and lower cups, bearings, crown race, star nut, shims, stem cap with 5mm integrated spacer and bolt - 1 Degree Adjustment - Long version is designed for headtube lengths between 115 - 140 mm

The 102BCD chainring was made specifically for the XTR M960 crankset - Only fits on the M960 crankset in the middle ring position - Drop-Stop technology. On Wolf Tooth's patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - These rings only fit on the M960 crankset in the middle ring position - If using a 9-speed drivetrain use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention) - 6mm chainring bolts needed - Chainline: 50mm - Use Drop-Stop A for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains DROP-STOP A - Wolf Tooth Drop-Stop A is the original patented wide/narrow chainring compatible with multiple drivetrain brands including 9, 10, 11, and 12spd SRAM Eagle, KMC, Wippermann, etc. - NOT compatible with 12spd SRAM Transmission (T-Type) Flattop, 12spd Shimano HG+, or 12spd Campy Recommendations - If you plan to ride in very muddy conditions, try using a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck Tech Specs: - Weight: 32t/47g - Material: 7075-T6 aluminum

- Bash guard protects chainring from logs, rocks and other trail hazards - Designed and manufactured in the USA from 7075-T6 aluminum alloy - See wolftoothcycling.com for mounting tips - 51g (26-30t)

Wolf Tooth was first to market with cyclocross 1x specific chainrings because we saw cyclocross as the perfect use for our patent pending Drop-Stop® technology. These beautifully machined 110 BCD asymmetric 4-bolt chainrings are optimized for your 1x Shimano CX / road / gravel drivetrain whether you run Dura Ace 9000, Ultegra 6800, 105 5800, or Tiagra 4700. They are also offset for the ideal 1x chainline. - Fits 110 BCD Asymmetric 4-bolt Shimano cranks - Drop-Stop technology. On Wolf Tooth's patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - Fits 110 BCD asymmetric 4-bolt cranks - All sizes compatible with Dura Ace 9000, Ultegra 6800, 105 5800, RS510, Tiagra 4700 or 4703, Sora R3000 or R3030, and Claris R2000 or R2030 cranks. - 38-50t are compatible with 105 R7000, Ultegra R8000, and Dura-Ace R9100. The 36t chainring is NOT compatible with these cranks. - NOT compatible with Dura-Ace R9200, Ultegra R8100, and 105 R7100 Cranks - Size 42t and larger will work with the Dura Ace 9100 power meter - Mounts in the big ring position of the cranks but is offset inward for perfect chainline. - The stock 2x bolts will not work. You will need our 6mm bolts which are optimized for single ring mounting. - If using a 9-speed drivetrain use a 10-speed chain. It fits tighter for better chain retention - Chainline 47.5mm - Use Drop-Stop B for all SRAM Eagle, SRAM Road and Transmission (T-Type) Flattop chains, 9, 10, and 11spd chains or 12spd KMC, Connex, Wippermann, Campagnolo. DROP-STOP B Compatible 9, 10, 11, and 12spd SRAM Eagle, 12spd SRAM Transmission (T-type) Flattop, 12spd Campy, 12spd KMC Not compatible with 12spd Shimano HG+ chains

These chainrings are for Shimano GRX cranks. They feature our patented Drop-Stop® design for the best wear life, chain retention, and mud clearance. Drop-Stop ST is specifically for the Shimano 12-speed Hyperglide+ chain, which is used by GRX 12-speed. Drop Stop-B works with all other 9, 10, 11, and 12-spd chains, including SRAM Flattop. Compatibility: - Shimano GRX cranksets including RX600 and RX810 - Drop-Stop ST is designed for Shimano 12-speed Hyperglide+ chains - Drop-Stop B tooth profile is compatible with SRAM Flattop chain - Wolf Tooth’s patented Drop-Stop wide/narrow tooth profile provides the ultimate chain retention and mud-shedding ability - Use Drop-Stop B for all SRAM Eagle, SRAM Road and Transmission (T-Type) Flattop chains, 9, 10, and 11spd chains or 12spd KMC, Connex, Wippermann, Campagnolo. DROP-STOP B Compatible 9, 10, 11, and 12spd SRAM Eagle, 12spd SRAM Transmission (T-type) Flattop, 12spd Campy, 12spd KMC Not compatible with 12spd Shimano HG+ chains

Wolf Tooth was first to market with Cyclocross 1x specific chainrings because we saw Cyclocross as the perfect use for our Drop-Stop® technology. Since their release, the uses for these rings has expanded beyond Cyclocross to commuting, gravel riding, mountain bikes with 5-arm crank power meters, and even full on-road applications with the giant 50t rings. Fits 110 BCD 5 arm cranksets Drop-Stop technology. On Wolf Tooth’s patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - These rings are for use with 110 BCD 5-arm cranksets. - Stock 2x bolts will not work. You will need bolts like our 6mm bolts which are optimized for single ring mounting. - Chainline - varies - these rings can be mounted in either the big or small ring position on a double cranksets. The most common mounting is in the big ring position because of chainstay clearance. The ring centerline is ~2mm from the ring's mounting face so they usually sit about 2mm closer to the frame than the stock big ring (depends on the stock ring) Recommendations - Recommend the use of a clutch-style rear derailleur for the best chain security. - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur! - Without these precautions, you may experience chaindrops and/or chainsuck. Tech Specs: - Weight: 34t/44g | 36t/58g | 38t/66g | 40t/74g | 42t/81g | 44t/90g | 46t/107g | 48t/115g | 50t/125g - Material: 7075-T6 aluminum - Made in the USA

Wolf Tooth was first to market with cyclocross 1x specific chainrings because we saw cyclocross as the perfect use for our Drop-Stop® technology. Since their release, the uses for these rings has expanded beyond cyclocross to commuting, gravel riding, and even full on-road applications with the giant 52t rings. - Fits 130 BCD 5 arm cranksets - Drop-Stop technology. On Wolf Tooth’s patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - These rings are for use with 130 BCD 5-arm cranksets. - Do NOT fit on the cranksets for Shimano DA 9000 / Ultegra 6800 - Not compatible with Campy CX10/11. - SRAM Exogram cranksets with inset nut must use stock fifth bolt + spacer(s). The Force CX1 bolt features a fifth bolt with 1x specific shoulder. This kit can be found online. - 38T important note: The chain may contact the spider arm slightly when using the 38T chainring (see last photo in the product images). We recommend filing a small chamfer on the spider arm but you can also just install it and let the chain do the work. This is only an issue with the 38T as the 130 BCD was designed for 39T smallest ring. - Stock 2x bolts will not work. You will need bolts like our 6mm bolts which are optimized for single ring mounting. Tech Specs: - Weight: 38t/52g | 40t/60g | 42t/62g | 44t/79g | 52t/132g - Material: 7075-T6 aluminum - Made in the USA - This 1x chainring and can be mounted in either the inner or outer ring position of a double crankset but can not be used in a 2x setup. - Chainline - The most common mounting is in the outer ring position because of chainstay clearance. The ring centerline is ~2mm from the ring's mounting face so they usually sit about 2mm closer to the frame than the stock big ring (depends on the stock ring) Use Drop-Stop B for all SRAM Eagle, SRAM Road and Transmission (T-Type) Flattop chains, 9, 10, and 11spd chains or 12spd KMC, Connex, Wippermann, Campagnolo. Recommendations - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck.

The GeoShift Performance Angle Headset allows you to adjust the geometry of your bike by changing the head tube angle, available in 1 or 2 degree options. This unique design lets the bearings sit at an angle to align with the steerer tube, preventing creaking noises commonly found with angle headsets that feature a spherical design. Reduce the head tube angle to make for slacker geometry and added stability on fast descents, or increase the angle using the opposite orientation of the headset, to make for steeper geometry and quicker steering with maximum front wheel traction. - Enduro black oxide coated chromium steel bearing included on both the upper and lower - Upper headsets ship with a star nut which can only be used on forks with steel or aluminum steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately) - Machined in the USA with lightweight, strong, durable aircraft-grade 6061 aluminum - Includes: Upper and lower cups, bearings, crown race, star nut, shims, stem cap with 5mm integrated spacer and bolt - 2 Degree Adjustment - Long version is designed for headtube lengths between 115 - 140 mm

The GeoShift Performance Angle Headset allows you to adjust the geometry of your bike by changing the head tube angle, available in 1 or 2 degree options. This unique design lets the bearings sit at an angle to align with the steerer tube, preventing creaking noises commonly found with angle headsets that feature a spherical design. Reduce the head tube angle to make for slacker geometry and added stability on fast descents, or increase the angle using the opposite orientation of the headset, to make for steeper geometry and quicker steering with maximum front wheel traction. - Enduro black oxide coated chromium steel bearing included on both the upper and lower - Upper headsets ship with a star nut which can only be used on forks with steel or aluminum steerer tubes. For forks with carbon steerer tubes you will need a compression plug (sold separately) - Machined in the USA with lightweight, strong, durable aircraft-grade 6061 aluminum - Includes: Upper and lower cups, bearings, crown race, star nut, shims, stem cap with 5mm integrated spacer and bolt - 2 Degree Adjustment - Short version is designed for headtube lengths between 90 - 115 mm

"The perfect solution when you need something smaller than a 30t on your 104/64 BCD cranks or your 11-speed Shimano XT and SLX 96/64 BCD cranks. Also, they look great when paired with our 104 BCD bash ring on a 104/64 BCD crankset - Fits any 104/64 BCD crankset (104 BCD is the middle/big position 64 is the smallest ring position) - Drop-Stop technology. On Wolf Tooth's patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility - Fits any 104/64 BCD crankset (104 BCD is the middle/big position 64 is the smallest ring position) - The Universal Model fits both 104/64 BCD cranksets and the Shimano 11 speed XT M8000 cranks and SLX M7000 cranks. - If using a 9-speed drivetrain use a 10-speed chain. It fits tighter for better chain retention - Chainline (approximate as BB centering and cranksets vary) - Chainline is 46mm on a triple and 48mm on a double crank - Chainline on a Standard M8000 or M7000 crankset is 48mm and 50mm on a boost version - You will use the stock bolts to mount to this chainring - Use Drop-Stop A for all 9, 10, 11 spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains Recommendations - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur! Wihtout these precautions, you may experience chaindrops and/or chainsuck"

The Wolf Tooth 76 BCD chainrings work great on any 76 BCD spider or crankset. These will replace the more expensive rings used on SRAM XX1 spiders or other manufacturer's spiders such as Cannondale. Also a great fit on the Specialized Stout crankset. - Fits any 76 BCD crankset or spider - Drop-Stop® technology. On Wolf Tooth's patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Note - Use standard M8 chainring bolts, not the M8.5 bolts included with XX1 spiders. Our patented Drop-Stop tooth design provides superior chain retention, wear life and mud-shedding capability. Compatibility: - These rings fit any SRAM 76 BCD spider or Specialized Stout crankset. Here are instructions on how to measure your BCD. - Threaded for standard M8 chainring bolts. For the XX1 spider, we recommend the 6mm bolts (or any short M8 chainring bolt). For the Stout crankset we recommend the 10mm bolts or the bolts that come with the crankset. - If using a 9-speed drivetrain use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention). Use Drop-Stop A or B for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains DROP-STOP A Wolf Tooth Drop-Stop A is the original patented wide/narrow chainring compatible with multiple drivetrain brands including 9, 10, 11, and 12spd SRAM Eagle, KMC, Wippermann, etc. Recommendations If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck Tech Specs: - Weight: 30t/45g | 32/51g - Material: 7075-T6 aluminum - Made in the USA

This 94 BCD 5-bolt ring will serve all your Vintage crankset and Surly OD crankset needs. - Fits any 94 BCD 5-bolt crankset (modification may be needed) - Drop-Stop technology. On Wolf Tooth’s patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - Four of the holes are threaded and one is a normal through bolt hole (done for Surly compatibility). Use a stock 10mm chainring bolt for the fifth, hidden arm. - These rings fit any 94 BCD 5 bolt crankset (possible alterations needed to fit some crankarms) - For Plus size bike applications with the Surly OD crankset, e.g. Instigator and Krampus, you will need to use the stock spacers (Spacer Kit QBP Part number CR8609) that came with your 1x setup. You will also need some 16mm bolts which can be purchased from Problem Solvers. - If using a 9-speed drivetrain use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention). - Provides a great chainline on most boost bikes. - Chainline (approximate as BB centering and cranksets vary) DROP-STOP A Wolf Tooth Drop-Stop A is the original patented wide/narrow chainring compatible with multiple drivetrain brands including 9, 10, 11, and 12spd SRAM Eagle, KMC, Wippermann, etc. Recommendations If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck. Tech Specs: - Weight: 28t/37g | 30/48g | 32t/57g - Material: 7075-T6 aluminum - Made in the USA

Looking for a SRAM XO1, X1, GX, and NX chainring with the proven chain retention of our patented Drop-Stop® chainrings? Wolf Tooth has what you need in these beautifully machined 94 BCD bolt-on chainrings. - Fits any 94 BCD SRAM crankset - Drop-Stop® technology. On Wolf Tooth’s patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - These rings fit any SRAM mountain bike crankset with a 94 BCD. Note that we also offer SRAM direct mount chainrings for standard, boost and BB30 short spindle cranksets and some stainless steel versions. - If using a 9-speed drivetrain use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention) - Chainline - 49mm - Provides a great chainline on most boost bikes. Use Drop-Stop A or B for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains DROP-STOP A Wolf Tooth Drop-Stop A is the original patented wide/narrow chainring compatible with multiple drivetrain brands including 9, 10, 11, and 12spd SRAM Eagle, KMC, Wippermann, etc. NOT compatible with 12spd SRAM Transmission (T-Type) Flattop, 12spd Shimano HG+, or 12spd Campy Recommendations - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck. Tech Specs: - Weight: 30t • 44g | 32t • 54g | 34t • 63g - Material: 7075-T6 aluminum - Made in the USA - US Patent 958123

This is a 96mm BCD chainring for a 1X chainring for XTR M9000 crankset with the proven chain retention of our Drop-Stop® chainring. They fit only the Shimano XTR M9000 and M9020 cranksets (race and trail respectively). They have an asymmetrical 96 mm BCD with built-in threaded standoffs to provide the ideal 1X chainline. - Fits 96 BCD XTR M9000 and M9020 cranksets - Drop-Stop technology. On Wolf Tooth's patented wide/narrow chainring, the wide side of the tooth has maximum contact on the drive side which spreads the load and improves chainring life. The narrow side allows clearance for mud and debris which reduces friction. - Alternating wide/narrow tooth pattern prevents chain derailment Compatibility: - These rings fit on the Shimano XTR M9000 and M9020 1x or 2x cranksets - Use only the stock Shimano XTR chainring bolts (M7x.75) - You will not use the stock bolt caps when mounting this ring. The stock bolts will thread into the chainring's standoffs from the outside of the crankset - For 1x9, 1x10, 1x11 and 1x12 drivetrains (including SRAM Eagle) If using a 9-speed drivetrain use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention) - Chainline - 49 mm for 30-34T and 50 mm for 36T. Provides a great chainline on most boost bikes - Available in multiple tooth profiles for optimal performance based on your chain type. Use Drop-Stop ST for use with Shimano 12-speed Hyperglide+ and 12spd KMC chains. Use Drop-Stop A for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains. Drop-Stop B is optimized for SRAM 12 spd Transmission (T-type) and Road Flattop chains but is compatible with all chains that work with Drop-Stop A. DROP-STOP A - Wolf Tooth Drop-Stop A is the original patented wide/narrow chainring compatible with multiple drivetrain brands including 9, 10, 11, and 12spd SRAM Eagle, KMC, Wippermann, etc. - NOT compatible with 12spd SRAM Transmission (T-Type) Flattop, 12spd Shimano HG+, or 12spd Campy DROP-STOP ST - Compatible with 12spd Shimano Hyperglide+ chain and 12spd KMC chain only - Symmetric Trapezoidal (ST) tooth shape is optimized for Shimano HG+ chain Recommendations - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck. Tech Specs: - Weight: 30/41g | 32t/50g | 34t/59g | 36t/69g - Material: 7075-T6 aluminum - Made in the USA

Looking for a 1X chainring for your new Shimano XT, SLX or Deore crankset with the proven chain retention of our Drop-Stop® chainrings? Wolf Tooth has what you need in the form of a beautifully machined asymmetrical 96 mm BCD that provides the ideal 1X chainline of 49mm. Note - The 28T and 26T sizes will mount to the inner 64 BCD mounting position on these cranksets. Compatibility: - These rings fit on the Shimano XT M8000, SLX M7000, Deore M6000, or FC M5100 1x or 2x cranksets - Not compatible with Deore triple (3x) cranksets - If using a 9-speed drivetrain use a 10-speed chain (shifts and works well on a 9-speed drivetrain and fits the ring tighter for better chain retention). - Provide a great chainline on most Boost bikes. See this explanation for details. - Drop-Stop A models will reduce the chainline (inward towards the frame) from the Shimano specified chainline for the crankset: 26T-28T = -3mm, 30T-34T = -2mm, and 36T-38T = -1mm - Drop-Stop ST models will have the same chainline as the Shimano specified chainline - 10mm bolts are optimized for mounting this ring - Available in multiple tooth profiles for optimal performance based on your chain type. Use Drop-Stop ST for use with Shimano 12-speed Hyperglide+ and 12spd KMC chains. Use Drop-Stop A for all 9, 10, and 11spd chains or 12spd SRAM Eagle, KMC, Connex or Wippermann chains. Drop-Stop B is optimized for SRAM 12 spd Transmission (T-type) and Road Flattop chains but is compatible with all chains that work with Drop-Stop A. DROP-STOP A - Wolf Tooth Drop-Stop A is the original patented wide/narrow chainring compatible with multiple drivetrain brands including 9, 10, 11, and 12spd SRAM Eagle, KMC, Wippermann, etc. - NOT compatible with 12spd SRAM Transmission (T-Type) Flattop, 12spd Shimano HG+, or 12spd Campy DROP-STOP ST - Compatible with 12spd Shimano Hyperglide+ chain and 12spd KMC chain only - Symmetric Trapezoidal (ST) tooth shape is optimized for Shimano HG+ chain Recommendations - If you plan to ride in very muddy conditions, we recommend a chainguide or chainkeeper in addition to a clutch-type rear derailleur. Without these precautions, you may experience chaindrops and/or chainsuck. Tech Specs: - Weight: 26t/42g | 28t/50g | 30t/41g | 32t/50g | 34t/59g | 36t/69g - Material: 7075-T6 aluminum - Made in the USA